CNC USB CONTROLLER MK2 SOFTWARE
This software is well made and will provide great functionality. The USB controller will only work with the Planet-CNC software. Y, and Z-axis does not work, it moves step motors and controller positions X -axis works, and Y and Z does not work.I used 425 oz-in motors 00.All have linked like a video USB CNC Controller/Interface Wiring Instructions Part 2, X - running. 1201., and got out of your USB controller $ 75. X - running and y and z-axis does not work, it moves step motors and controller positions X -axis works, and Y and Z does not work.Ĭlick the link to add information to this solution: I installed the USB CNC Planet software. A simple multimeter(ohm's) will work, just connect the positive and negative ends to one side of the same wire and if reading comes to 0.000, wire has continuity and if reads 0.L then there is a break in the wire and should be replaced.Ĭlick the link to add information to this solution: I installed the USB CNC Planet and got out of your USB controler $ 75. Next test if first fails, is to check continuity in your wires. If tests failed and working (x-axis setup) does not working in the new axis location, go the Planet-CNC/File/Settings/Axes and check if your current non-working axis setup requires a inverted pulse. Recommend first test to check a non-working axis, is to connect the current working axis(ex X-axis) to either the y/z axis to test the actual board and wiring in other axis setup. Our blackTooth Laser Cutter: Our greenBull Leaser/Spindle Head: The CNC Machine: The Laser/Spindle Head: Ĭlick the link to add information to this solution: Requirement of laser cutting CNC Router having working area: 100cm x 100cm x 300cm, Belt driven motion, servo motor controller Rather, we use precision stepping motors instead. Generally, the laser function is not tied to the working area unless the laser tube is stationary, where the farther the beam has to travel, the less energy results at the intended area (on the surface of the material). The requirement of a laser cutter is having a laser with enough energy output to cut the intended material. This is an open ended question to which there could be many possible answers. The Pokeys57CNC board is the mose feature rich and will work with both Mach3 and Mach4: The MAch3 USB board is a good inexpensive interface that will work well if you need the interface to be USB only: Our in-house parallel breakout board (ytou need a parallel port for this interface to work): Most motherboards have the parallel port connector on the motherboard, but not as a connector on the back of the computer case.Ĭlick the link to add information to this solution: Do you sell the 3 axis electronics combo, for heavy gantry, with the new Planet CNC usb controller ? We do sell three other boards that may work for you. They made a change to their software that prohibits us from creating the open source board. Unfortunately, we don't sell the planet-cnc controller anymore. Other Possible Solutions to this Question
CNC USB CONTROLLER MK2 FREE
Also, feel free to contact our sales department for a quote if you need a custom assembly. We have all the parts you would need to add laser functionality to your machine here:, if you feel comfortable assembling your own package. Here is an example of a combination spindle/laser mount for our greenBull machine. That said, our machines will accept a laser head either in lieu of or in addition to a spindle. This allows maximum flexibility for the customer to choose their own preferred software for this part of the toolchain. The machines themselves will accept standard signals from a wide variety of machine control systems, not just PlanetCNC or Mach3. For the second question, it is important to note that BYCNC machines are not based on PlanetCNC software, or any other particular machine control system. The typical modification is to use the Z axis down signal to fire the laser, analogous to an endmill cutting into the workpiece from an initial position above it. The PlanetCNC USB software, like most machine control software, can be used to control a laser engraver/cutter. Can the Planet CNC USB controller be used with a laser engraver/cutter? Can the build your own CNC based on the Planet CNC USB controller accept a Laser head instead of a router? Current Solution